Part Number | Laser | Distance | Interface | Temp | DDMI | Note |
ASP010I01310010 | 1310nm DFB | 10km | LC | I-temp | Yes |
Parameter | Symbol | Min. | Typ. | Max. | Unit | Note |
Storage Temperature | Ts | -40 | - | 85 | ºC | |
Relative Humidity | RH | 5 | - | 95 | % | |
Power Supply Voltage | VCC | -0.3 | - | 4 | V | |
Signal Input Voltage | Vcc-0.3 | - | Vcc+0.3 | V |
Parameter | Symbol | Min. | Typ. | Max. | Unit | Note |
Case Operating Temperature | Tcase | -40 | - | 85 | ºC | Industrial |
Power Supply Voltage | VCC | 3.14 | 3.3 | 3.47 | V | |
Power Supply Current | ICC | - | 490 | mA | ||
Data Rate | BR | 10.3125 | 11.3 | Gbps | ||
Transmission Distance | TD | - | 1 | km | 9/125 SMF |
Parameter | Symbol | Min | Typ | Max | Unit |
Transmitter | |||||
Average Launched Power | POUT | -1 | 4 | dBm | |
Center Wavelength | λc | 1270 | 1310 | 1355 | nm |
SMSR | 30 | dB | |||
Optical Extinction Ratio | ER | 3.5 | dB | ||
Spectral Width (-20dB) | s | 1 | nm | ||
Transmitter OFF Output Power | POff | -30 | dBm | ||
Transmitter and Dispersion Penalty | TDP | 3.2 | dB | ||
Output Eye Mask | Compliant with IEEE 802.3ae | ||||
Receiver | |||||
Wavelength Range | λ | 1260 | 1565 | nm | |
Receiver Sensitivity@9.953 Gb/s | RSENS | -14.4 | dBm | ||
Receiver Sensitivity@11.3 Gb/s RSENSE |
RSENS |
-12.6 |
dBm | ||
Input Saturation Power (Overload) | Psat | 0.5 | dBm | ||
Receiver Reflectance | Rrx | -27 | dB | ||
LOS De -Assert | LOSD | -26 | dBm | ||
LOS Assert | LOSA | -28 | dBm |
Notes:
1. Launched power (avg.) is power coupled into a single mode fiber with master connector.
2. lc refer to the selected wavelength as listed in the wavelength selection table.
3. Measured at 1528~1600nm,ER>8.2dBm, PRBS 231-1 and BER better than or equal to 10E-12; Measured with 80km transport
4. Measured at 1528~1600nm,ER>8.2dBm, PRBS 231-1 and BER better than or equal to 10E-12; Measured with 80km transport.
Electrical Characteristics
Parameter | Symbol | Min | Typ | Max | Unit |
Supply Voltage | Vcc | 3.14 | 3.3 | 3.46 | V |
Supply Current | Icc | 490 | mA | ||
Transmitter | |||||
CML Inputs | Vin | 150 | 1200 | mVpp | |
Single ended data input swing | Vin,pp | 180 | 700 | mV | |
Transmit Disable Voltage | VD | 3.45 | V | ||
Transmit Enable Voltage | VEN | Vee | Vee+ 0.3 | V | |
Transmit Disable Assert Time | 10 | us | |||
Receiver | |||||
Differential data output swing | Vout,pp | 350 | 700 | mV | |
Data output rise time | tr | 28 | ps | ||
Data output fall time | tf | 28 | ps | ||
LOS output high level | VLOS-H | 2.0 | VccHOST | V | |
LOS output low level | VLOS-L | Vee | Vee+0.8 | V | |
Power Supply Rejection | PSR | 100 | mVpp |
Notes:
1. Measured with receive Pin=Psen, Vcc=3.3V, operation temperature range without air flow.
2. Connected directly to TX data input pins. AC coupled thereafter.
3. Or open circuit.
4. Into 100 ohms differential termination.
5. These are unfiltered 20-80% values
6. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
7. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network.
Pin Assignment
Pin | Symbol | Name/Description | NOTE |
1 | V EET | Transmitter Ground (Common with Receiver Ground) | 1 |
2 | T FAULT | Transmitter Fault. | 2 |
3 | T DIS | Transmitter Disable. Laser output disabled on high or open. | 3 |
4 | SDA | 2-wire Serial Interface Data Line | 4 |
5 | SCL | 2-wire Serial Interface Clock Line | 4 |
6 | MOD_ABS | Module Absent. Grounded within the module | 4 |
7 | RS0 | Rate Select 0 | 5 |
8 | LOS | Loss of Signal indication. Logic 0 indicates normal operation. | 6 |
9 | RS1 | No connection required | 1 |
10 | V EER | Receiver Ground (Common with Transmitter Ground) | 1 |
11 | V EER | Receiver Ground (Common with Transmitter Ground) | 1 |
12 | RD- | Receiver Inverted DATA out. AC Coupled | |
13 | RD+ | Receiver Non-inverted DATA out. AC Coupled | |
14 | V EER | Receiver Ground (Common with Transmitter Ground) | 1 |
15 | V CCR | Receiver Power Supply | |
16 | V CCT | Transmitter Power Supply | |
17 | V EET | Transmitter Ground (Common with Receiver Ground) | 1 |
18 | TD+ | Transmitter Non-Inverted DATA in. AC Coupled. | |
19 | TD- | Transmitter Inverted DATA in. AC Coupled. | |
20 | V EET | Transmitter Ground (Common with Receiver Ground) | 1 |
Notes:
1. Circuit ground is internally isolated from chassis ground.
2. TFAULT is an open collector/drain output, which should be pulled up with a 4.7kΩ– 10 kΩ resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V.A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V.
3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
4. Should be pulled up with 4.7kΩ- 10kΩ on host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in.
5. Internally pulled down per SFF-8431 Rev 4.1.
6. LOS is open collector output. It should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
Copyright 2022 ATI. All rights reserved.
Copyright 2022 ATI. All rights reserved.
